DMP Electronics Security Command 690 Uživatelský manuál stáhnout pdf (Strana 7)

SYSTEM ARMING AND DISARMING FOR AN AREA SYSTEM

Area Assignment: The Area Arming system can contain from one

to four individual areas. Your burglary alarm system has been

divided into ___ separate areas. The specific area names should be

listed below for easy reference.

Area Name

_______-_______________________

Arming or Disarming: The first choice to be made is if you wish

to arm or disarm. Arming or disarming may be done for all areas at

one time or each area may be controlled individually. If a code

number is required you will only be allowed to control the areas

which are assigned to your code number.

Arming: When arming is selected a code number may be required.

This is optional. The option is programmed during system installa-

tion. If a code number is required you will only be able to arm the

areas which are assigned to your code number. If no code number

is required you will be able to arm all areas.

All Or Selective Arming: After entering your code number you will

be asked if you wish to arm all of the areas to which you have access

or only selected areas. If you choose to arm all areas the system will

begin checking to see that all loops are in a good condition. If you

choose to arm selective areas the SECURITY COMMAND will allow

you to choose the individual areas you want to arm before beginning

the loop check.

Bypassing: After you have made your arming selection the

SECURITY

COMMAND will display any loops which have been bypassed prior

to arming . This is for your information only and they may not be reset

during arming. They will remain bypassed until disarmed or reset.

Any 24 hour loops which are in a bad condition will also be displayed.

The system will then check to see that all doors and windows which

will be armed are closed and that any motion detectors, etc., are set

properly. If no problems exist the areas you have selected will be

armed. If a problem does exist on one or more loops the SECURITY

COMMAND will display the problems and allow you to bypass those

loops. If the problems can be corrected by simply closing a door or

window you should not bypass. You should correct the problems

and repeat the arming procedure. If the loop or loops are in some

way damaged and cannot be corrected they may be bypassed.

Bypassing a loop means it will be ignored while the system is armed.

A code number may be required to bypass. This is optional and is

programmed during system installation.

Armed Message: After all loops are bypassed or corrected the

areas you selected will be armed. The SECURITY COMMAND will

display “ALL SYSTEM ON” if all areas are armed. The display will

read “SYSTEM ON” if all areas are not armed. The display will then

show you the exit delay. Any exit loops will not be armed until the

delay expires. All other non-exit loops are armed immediately.

One Moment Message: Your system may be programmed to wait

for the transmission of the arming signal to the central station

receiver before displaying the Armed Message. This is to insure that

your phone lines are working properly. While the system is waiting

for the transmission the display will read “ONE MOMENT...”. If the

test is okay the Armed Message will be displayed. If the test fails the

DOOR ACCESS

3. Enter your code number and press . The dis-

play will read

DETECTORS OFF then change to DETECTORS

ON to confirm that the smoke

detectors have been reset.

User Code Level: 1- During permanent or temporary

schedules only

3- Anytime

Function: To operate the door strike

Door Access is used to operate the door strike at a single

SECURITY COMMAND

When Door Access is selected you will be asked to enter your code

number. When the code number is accepted the door strike at the

SECURITY COMMAND you

are operating will turn on for five seconds.

Door Access also functions any time any area of the system is

disarmed at the door strike keypad or by simply entering your code

number and pressing COMMAND.

A report of this entry can be transmitted to your central station. This

report is optional and is programmed during system installation.

Step By Step:

1. Press the key until DOOR ACCESS? is

displayed.

2. When DOOR ACCESS? is displayed press any one of the

top four

select keys. The display will read ENTER CODE: - .

3. Enter your code number and press . The door strike will

turn

on for five seconds.

COMMAND

1 2 3 4 5 6 7 8 9 10 11 12 ... 16 17

Komentáře k této Příručce

Žádné komentáře

DMP Electronics Security Command 690 Uživatelský manuál Strana 7

Komentáře k této Příručce

Související produkty a manuály pro Numerické klávesnice DMP Electronics Security Command 690