Dmp-electronics DMP Command Processor Panel XR500 Uživatelský manuál stáhnout pdf (Strana 20)

XR500 Series Canadian Programming Guide Digital Monitoring Products

COMMUNICATION

3.22

RETRY SECONDS: 6

Retry Seconds

This option displays for NET or 232 Communication Types.

Enterthenumberofseconds(between6and15)thepanelshouldwaitbefore

retrying to send a message to the receiver if an acknowledgment was not received.

The panel retries as many times as possible for a period of one minute before

sending a network trouble message. For example, if retry time is set to 15, the

panelretriesfourtimes.ThedefaultRetryTimeis6seconds.

Note:IfTCPisenabled,theminimumRetryTimeprogrammedis6seconds.

3.23

SUB CODE NO

Substitution Code

ThisoptiondisplayswhentheCommunicationTypeisNET,CELLor232.ThePanel

Substitution Code increases the level of security by helping to ensure that the panel

sending the message to the receiver has not been substituted by another panel. The

default is NO.

Select YES to send a substitution code with every message.

SelectSHARED(SHR)tousethesamesubstitutioncodeasoperatingintheprevious

path.

3.24

232 COMM PORT: O

232 Communication Port

This option displays when Communication Type is 232.

ThisoptionsetsthephysicalRS-232porttotheon-boardconnectororoneoftheDMP

Model461InterfaceAdaptorCardslotslabeledA,B,C,D,orE.UseslotAifusinga

462NNetworkInterfaceCardwithorwithoutthe461card.

EnterOtousetheon-boardconnector.SettheXR500SeriesCanadianpanelJ23

jumpertoRandbrieyresetthepanelusingtheJ16jumpertoactivateRS-232

operation.DefaultisO(On-board).

3.25

232 SETUP:

232 Setup String

This option displays when the Communication Type is 232. Enteruptotwolinesof16

characters to equal up to 32 characters for the destination address that may include

an IP address. Example: If using a DMP iCOM, enter AT#UCXXX.XXX.XXX.XXX#PPPPP

where X is the IP address and P is the port number.

3.26

893A: NO YES

893A

This option displays when the Communication Type is DD or CID.

The893AoptionallowsreportstobesenttothereceiveronasecondDDlineusing

the893Amodule.DefaultisNo.

Whenusingthisoption,TestReportmessages(S07AutomaticRecallTestor

S88UnrestoredSystemRecallTest)aresenttothereceiveratthefrequency

programmedinTestFrequency,alternatingbetweentherstandsecondphoneline.

Forexample,aDDpathwithan893Amodulesetfordailytestreportfrequency

sends a test report through phone line 1 one day and phone line 2 the next day.

If893AoptionissettoYES,enteruptoa3digitprextobedialedbeforethe

secondphonenumber.Ifnoprexisentered,thesecondphonenumberisdialedas

originally entered.

3.27

ALARM SWITCH: 1

Alarm Switch

This prompt displays for DD or CID Communication Types.

Enter the number of attempts to send an alarm message before switching to the next

path.Rangeisfrom1to10.Allnon-alarmmessagesaresentfor10attemptsonthe

dialer before a switch is initiated. If the path immediately following this channel is

not a backup path, this option has no effect. Default is 1.

3.28

DUPLICATE ALARMS

Duplicate Alarms

This prompt displays for BACKUP paths. If Yes is selected, the current backup path

duplicates all alarms occurring on its group primary path. Default is No.

D E

O A B C

NO YES SHARED

NO YES

2ND LINE PREFIX:

1 2 ... 15 16 17 18 19 20 21 22 23 24 25 ... 84 85

Komentáře k této Příručce

Žádné komentáře

Dmp-electronics DMP Command Processor Panel XR500 Uživatelský manuál Strana 20

Komentáře k této Příručce

Související produkty a manuály pro Bezpečnost Dmp-electronics DMP Command Processor Panel XR500