Dmp-electronics DMP Command Processor Panel XR500 Uživatelský manuál stáhnout pdf (Strana 32)

XR500 Series Canadian Programming Guide Digital Monitoring Products

REMOTE OPTIONS

7.6 PC Modem

YESallowsthepaneltoanswerthetelcolinkandconnectwithRemoteLinkthrough

the PC Modem at 2400 baud. NO disables PC Modem communication.

7.7

ALR RCVR NO YES

Alarm Receiver Authorization

Select YES to enable remote commands and programming to be accepted from the alarm

SCS-1RReceiver.TheRemoteKeyoptioncanalsoberequired.

WithYESselected,thepanelrequeststhereceiverkeyduringitsrstcommunication

withtherstSCS-1RReceiver.Thepanelretainsthisalarmreceiverkeyinmemoryand

allows remote commands to be accepted from the alarm receiver. If an alarm occurs

during a remote connect, the alarm report is immediately sent to this receiver only.

When NO is selected, remote commands and programming are not accepted from the

alarmSCS-1RReceiver.

7.8

SVC RCVR NO YES

Service Receiver Authorization

YES enables remote commands and programming to be accepted from a secondary

servicereceiverotherthanthealarmSCS-1RReceiver.TheRemoteKeyoptioncanalso

be required.

WithYESselected,thepanelrequeststheservicereceiverkeythersttimeitis

contacted by the service receiver. The panel retains this service receiver key in memory

and accepts remote commands from the service receiver.

If an alarm occurs during a remote connect, the panel disconnects from the service

receiver and calls the alarm receiver. Alarm reports are only sent to the alarm receiver.

It is important that the alarm receiver key and the service receiver key programmed at

the central station are NOT the same so the panel can determine the difference between

receivers.

When NO is selected remote commands and programming are not accepted from a

secondary service receiver.

This option must be YES to allow programming from a directly connected computer or an

iCOM/iCOM-E.

7.9 Manufacturer Authorization

Select YES to allow DMP Technical Support technicians to access the panel during

system service or troubleshooting. This authorization automatically expires within

one hour.

DMP remote service is provided on a read only basis: DMP technicians can look

at the system programming and make suggestions only. Alterations can only be

accomplished by installing company service personnel.

7.10 Allow Network Remote

This option displays only if the panel has network capability. YES allows remote

programming over the network. Changing this prompt does not change any other

network programming prompts. Default is YES.

7.10.1

NETWORK PROG

Network Programming Port

PORT: 2001

Entertheprogrammingportnumber.Theprogrammingportidentiestheportused

to communicate messages from the panel. The default Programming Port setting is

2001.

7.10.2 Encrypt Network Remote

YES encrypts data sent over network. Default is NO.

7.11 Allow Cellular Remote

YES allows remote programming using cellular connection. Default is YES.

7.11.1 First GPRS APN

EntertherstAPN(AccessPointName).Thisallowsanaccesspointforcellular

communication and is used to connect to a DNS network. The APN may contain two

linesof16characterstoequal32characters.DefaultissettoNMRX.CA.APN.

Second GPRS APN

EnterthesecondAPN(AccessPointName).Thisworksasabackupincasetherst

APNfails.TheAPNmaycontaintwolinesof16characterstoequal32character

Default is set to INTERNET.COM.

PC MODEM NO YES

MANUFACTURER

AUTH? NO YES

ALLOW NETWORK

REMOTE? NO YES

NMRX.CA.APN

FIRST GPRS APN:

INTERNET.COM

SECOND GPRS APN:

ENCRYPT NETWORK

REMOTE? NO YES

ALLOW CELL

REMOTE? NO YES

1 2 ... 27 28 29 30 31 32 33 34 35 36 37 ... 84 85

Komentáře k této Příručce

Žádné komentáře

Dmp-electronics DMP Command Processor Panel XR500 Uživatelský manuál Strana 32

Komentáře k této Příručce

Související produkty a manuály pro Bezpečnost Dmp-electronics DMP Command Processor Panel XR500