Dmp-electronics DMP Command Processor Panel XR500 Uživatelský manuál stáhnout pdf (Strana 55)

Digital Monitoring Products XR500 Series Canadian Programming Guide

AREA INFORMATION

18.5

CLS CHK NO YES

Closing Check

Select YES to enable the panel to verify that all areas in the system are armed

afterpermanentorextendedschedulesexpire.IftheClosingCheckndsanyareas

disarmed past the sched uled time, the keypads selected to display System Trouble

StatusdisplaysCLOSINGTIME! and emits a steady beep. When Area Schedules is set

toYESinAreaInformation,thespecicareaandnamedisplayfollowedby—LATE.

When Auto Arm is NO, if within ten minutes the system is not armed or if the

scheduleisnotextended,aLatetoClosereportissenttotheSCS-1RReceiver.

When Auto Arm is YES, the area arms. See Automatic Arming section.

If the area becomes disarmed outside of any schedule, the Closing Check sequence

occursaftertheLateArmDelaytime.SeeLateArmDelay.

When Closing Check is NO and Auto Arm is YES, the system immediately arms when

the schedule expires. No warning tone occurs.

In addition, when Closing Check is NO, the option to extend a schedule does not

display when the schedule expires.

18.6

CLS CODE NO YES

Closing Code

When YES is selected, a code number is required for system arming. If NO is

selected, a code number is not required for system arming.

18.7

ANY BYPS NO YES

Any Bypass

When YES is selected, zones can be bypassed without a code number during the

arming sequence. A code number is always required to use the Bypass Zones option

from the menu.

18.8

AREA SCH NO YES

Area Schedules

Select YES to allow each area to set its own shift schedules 1 to 4. Enter NO to

provide one set of schedules for this system.

Note:AreaSchedulesarenotdesignedtooperatewithAll/PerimeterorHome/

Sleep/Awaysystems.

18.9

EARLY AMBUSH: 0

Early Morning Ambush (XR500N/XR500E only)

Enterthenumberofminutes(1to15)beforeasilentalarm(EarlyMorningAmbushS33)

issenttothecentralstationusingthearea1accountnumber.Enter0(zero)todisable

this option.

When a user code is entered to disarm area 1 at a keypad or reader with Access

Areas assigned to area 1, the same or different user code must be entered within the

programmed number of minutes to prevent an ambush message from being sent to

the receiver. The second user code also must have authority to disarm area 1.

In addition, a zone activation with Alarm Action Message C also cancels the Early

Morning Ambush timer and stops an Ambush message from being sent to the receiver.

See Report to Transmit section in Zone Information.

The keypad does not display any indication that the ambush timer is running.

Indications can be provided by assigning an output number to Entry Out and Ambush

Out in Output Options. Entry Out turns on one minute before the timer expires and

turns off at expiration. Ambush Out turns on at the timers’ expiration and turns off

when Sensor reset is performed.

18.10

AREA NO: -

Area Number

Enter the number of the area to program. After entering the area number, press

COMMAND to enter the area name. Only Area systems allow the area name to be

changed.

Note:WhenAll/PerimeterorHome/Sleep/Awayisselectedasthesystemtype,the

Area Number does not display.

1 2 ... 50 51 52 53 54 55 56 57 58 59 60 ... 84 85

Komentáře k této Příručce

Žádné komentáře

Dmp-electronics DMP Command Processor Panel XR500 Uživatelský manuál Strana 55

Komentáře k této Příručce

Související produkty a manuály pro Bezpečnost Dmp-electronics DMP Command Processor Panel XR500